Elby CloneBD 1.3.2.0 Beta (64bit/32bit)

ericlien

	1.0.3.2 2015-02-26 - new: added new sound files - new: added sound when CloneBD requests to swap the medium for burning - new: limit burn speed to 6x, because supported speeds reported by the drive are sometimes far higher than possible. Can be switched off in settings (use with caution! Too high speeds can result in write errors) - change: when source medium gets removed (e.g. for inserting a recordable disc for writing), hide navigation buttons "input" and "selection". - fix: potential problem when removing subpath streams from playlists - fix: when source and destination drive are the same, disc title and disc thumbnail weren't shown on completion page - fix: log file was missing line breaks, when unicode characters were logged. - fix: crash when the drive is removed due to read errors - fix: with single file creation, a change of the destination path sometimes got ignored. [#2602] - fix: audio removal at beginning of stream [#2645 #2625] - fix: prevent a possible late registration of audio streams - fix: verify against invalid stream context - fix: verify against out-of-memory allocations - fix: transcoding startup issues on some older CPU - fix: transfer unknown audio packets when filtering - some minor fixes and improvements - updated languages http://elby.ch/download/SetupCloneBD.exe

ericlien

	1.0.3.3 2015-03-11 - fix: crash when creating log file after source disc was removed. - fix: audio delay with some streams (too much audio, or audio behind video) - fix: Burner SDK bug writing sectors twice, then aborting with ERROR 4 - fix: audio sync issues (file output) - fix: audio sync issues on some streams - fix: selection panel sometimes did not honor the "single subtitle" flag in presets. - fix: processing of very large SEI in AVC (x264 encoding settings go on forever) - fix: allow more frame extensions (increased to 64 sub-frames) - fix: handling of AC-3 descriptors that are incorrectly used on BD following DVB spec - some minor fixes and improvements - updated languages http://elby.ch/download/SetupCloneBD.exe

ericlien

	1.0.3.4 2015-03-19 •change: reduced the expected capacity for blu-ray media slightly •change: sorting order of audio streams in file/device output •change: optimize PMT (Program Map Table) generation •change: added more attribute information to PSI (Program Stream Information) structures in m2ts •fix: some partial copies would not play beyond the menu. Removing IM Sync type subpaths now to fix this. •fix: check some out-of-memory conditions (fixes some crashes) •fix: misidentified PIDs in PiP substreams, caused problems with subtitles on some discs •minor fixes and improvements •updated languages http://elby.ch/download/SetupCloneBD.exe

ericlien

	1.0.3.5 2015-03-24 - new: down convert HD audio to AC3 when creating BD copies. - change: improved resize and initialize behavior of language box on selection page. - change: allow selection of burn speeds (2x, 4x, 6x) even when type of medium is unknown (source drive = destination drive) - change: improved output size estimation should be more accurate now, especially, when not using video compression. - minor fixes and improvements - updated languages http://elby.ch/download/SetupCloneBD.exe

ericlien

	1.0.3.7 2015-03-26 •fix: estimator values were not correctly retrieved from cache •fix: chapter mark filtering in clipping mode. •fix: improved error detection when video encoder fails •fix: properly add .mkv/.mp4 chapter markers •fix: encoding of large video frames (> 1 MiB) •updated languages http://elby.ch/download/SetupCloneBD.exe

ericlien

	1.0.3.8 2015-03-27 - fix: asynchronous writer would not flush data, which broke short files (also caused SpeedMenus to fail) - fix: watermark detection was broken - new: allow direct jump to main title (bypassing the menu) on playback of converted discs - updated languages http://elby.ch/download/SetupCloneBD.exe

ericlien

	1.0.3.9 2015-04-10 - new: display estimated uncompressed output size on selection page, when creating partial BD copies. [#656] - new: add burner log to CloneBD log file to further study spurious write errors on BD-Rs - change: improved secondary video size estimation - change: improved drop clips with differing streams/missing audio on MKV/MP4 encode [#3287] - change: copy instead of compress secondary video - change: size units for KB, MB, GB, TB have been changed from IEC "binary representation" (1024^x) to SI (decimal) representation (1000^x) to better match the sizes of storage media and for less confusion. If IEC values are to be displayed, they will be denoted with KiB, MiB, GiB, ... respectively. - change: ensure user can't manually specify a non-empty temp path, as this can cause the result to be too large for the blank disc (append a postfix, if nonempty temp was specified) [#3346] - change: log actual sectors when encountering read errors - fix: skip unsupported CC in MPEG-2 [#2104] - fix: support for very chatty x264 encoder used on some BDs - minor fixes and improvements - updated languages http://elby.ch/download/SetupCloneBD.exe

ericlien

	1.0.4.0 2015-04-11 - change: disc hash includes additional files to better detect differences caused by decryptor tools - change: extended burner logging - fix: remove path delimiters from disc descriptions when deriving mkv/mp4 filenames. [#3460] http://elby.ch/download/SetupCloneBD.exe

ericlien

	1.0.4.1 2015-04-12 - fix: sometimes convert uncompressed even through compression was selected. [#3487, #3163, #3465, #3467] - fix: installer will no longer try to install files after a reboot, but throw an error message instead, if a file can't be written (reported by Ch3vr0n) - updated languages http://elby.ch/download/SetupCloneBD.exe

ericlien

	1.0.4.2 2015-04-15 - improved: rate plotter - improved: remaining time prediction - improved: added overhead data to estimation when doing complete copies (in some cases JAR folders are enormous) - change: make slider automatically adjust to disc size on target page, if destination drive is not the same as source drive. - change: timeout estimator bar in case a packet could not be retrieved (otherwise Go-button would remain disabled) - fix: when burning multiple discs in a row, read/write error counts were not reset. - fix: uncompressed copies had a tendency to overshoot estimated output size. Now estimating video bitrate less conservatively. - fix: trim paths entered by user, to remove trailing spaces. - fix: "Go" button sometimes did not refresh correctly, when state changes from disabled to enabled (would appear disabled, until hovered with mouse) - fix: burner logging crashed and required overly huge memory blocks - minor fixes and improvements - updated languages Download: http://elby.ch/download/SetupCloneBD.exe